Exactly How to Replace a Tub Yourself: Removing and Replacing.

Booking Page

Each person will have their own assumption with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Mounting a bathtub isn't specifically rocket science, however it does require strong plumbing, woodworking, and often, tiling abilities. Replacing an old bath tub with a new one is also a moderately hard job. If the old bathtub is readily easily accessible, the task can move immediately; if you have to open a wall surface to remove the old tub and also place the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub and set in the brand-new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. As opposed to hiring a professional to take control of a halfway-completed task, it is better to think about utilizing one prior to you start. Chances are you may need a professional plumber to make tube connections.
This post will certainly aid you mount a brand-new bath tub in your bathroom if you have already acquired a brand-new tub and don't need to alter the setup of your previous water supply pipes.
Your tools as well as material checklist ought to make up the following:

New Bathtub

Hammer

Pipe Wrenches

Prybar

Shatterproof glass

Degree

Pliers

Adjustable Wrench

Putty Knife

Screwdriver

Cold Blade

Tape Measure

Pipeline Caps

Removing Old Touches

If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is detach the water. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing taps can be quite problematic because of the limited accessibility that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have actually been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before going on to fit the brand-new faucets, compare the pipe connections on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.

Suitable New Taps

If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making certain that the washing machines are in area in between the tap and also the sink. Safeguard the tap in place with the supplier supplied backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The former type must be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

Mounting the Bathtub

Utilizing the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 little factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the bath tub until the level reads degree.
To install faucets, fit the bottom of the furthest adaptable tap adapter to the appropriate supply pipeline by making a compression join; after that do the very same for the other faucet.
Switch on the water system and inspect all joints and also new pipework for leakages and also tighten them if required. Load the bathtub as well as additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as described in the producer's user's manual. Tiling and sealing around the bath tub should wait up until the bath tub has actually been used a minimum of when as this will settle it right into its last position.

Getting ready for the Installment

Firstly, the supporting framework provided with the bath ought to be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make certain that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final setting.

Tiling Around the Tub

In the location where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall surface between the bath as well as the tiling, resulting in problems with moisture as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components and also installations. They are offered in tubes as well as cartridges, as well as are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealant can fracture rather very early if you do not take into consideration this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently offered on the market. It is advisable to fit the floor tiles making use of water-resistant or waterproof glue and also grout.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

Hopefully you liked our part about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you so much for taking the time to read through our piece of content. Liked our post? Please share it. Let other people find it. Thanks for going through it.

Book Your Installation